Services and Products

  1. 1.0 GHz to 4.0 GHz Dual Band Solid State Amplifiers: AS0104 Series

    This series of solid state amplifiers have been designed to cover the 1.0 GHz to 4.0 GHz frequency range in two bands (1 GHz to 2 GHz and 2 GHz to 4 GHz). Several models are available with 30W/17W, 30W/30W, 55W/17W, 55W/30W, 55W/55W, 100W/17W, 100W/55W, 100W/100W, 200W/100W, 200W/200W, 400W/100W, and 400W/200W P1dB levels. Information on specifications can be accessed on the datasheets below.

  2. Solid State Broadband High Power Amplifier: 1163-BBM2E3KLO

    This solid state broadband high power amplifier operates in the 20-520 MHz frequency range and delivers 125 Watts output power. It’s suitable to use as a broadband PA building block in applications involving electronic attack, digital communications, and test and measurement in the UHF/VHF bands.

  3. Amplifier Module: 2110-2170MHz (50 Watts): GCM5C5DHO (SKU 3114)
    This is a compact, high power amplifier module with stop frequencies from 2110 MHz to 2170 MHz ideal for broadband mobile jamming and band specific high power linear applications. It features high reliability and ruggedness, a small form factor along with a light weight, built in control, monitoring, and protection circuits, 50 ohm input/output impedance, a solid-state class AB linear design, and more. High power advanced GaN devices are used in order to achieve good power density, high efficiency, a wide dynamic range, and low distortions.
  4. Microwave Solid State RF Power Amplifier: Model 8100-052

    ETS-Lindgren offers the Model 8100-052 microwave solid state power amplifier (PA) specifically designed for EMC applications that include IEC 61000-4-3, 30 V/m automotive requirements. This 500 W PA utilizes GaAs technology, and delivers an improved design and higher efficiency performance over silicon-based amplifiers.

  5. Model 500A250B -- 500-Watt, Solid-State Amplifier

    The Model 500A250B is a self-contained, air-cooled, broadband, completely solid state amplifier designed for applications where instantaneous bandwidth and high gain are required. Push-pull LDMOS circuitry is utilized in all high power stages in the interest of lowering distortion and improving stability.

  6. X-Band Solid-State Power Amplifier: SSPA 9.0-10.0-40
    Aethercomm Part Number SSPA 9.0-10.0-40 is a high power, X band, Solid State Power Amplifier that operates from 9.0 to 10.0 GHz. The saturated output power is 40 watts typical at 25ºC. Typical small signal gain is 58 dB. Noise Figure is 10.0 dB typical at 25ºC. Input VSWR is 2.0:1 maximum. Output VSWR is 2.0:1 maximum.
  7. X-Band Solid-State Power Amplifier: SSPA 8.5-9.6-30-28V
    Aethercomm Part Number SSPA 8.5-9.6-30-28V is a high power, X Band, Solid State Power Amplifier that operates from 8.5 to 9.6 GHz. The saturated output power is 30 watts typical at 25ºC. Typical small signal gain is 50 dB. Noise Figure is 10 dB typical at 25ºC. Input VSWR is 2.0:1 maximum. Output VSWR is 2.0:1 maximum. This unit is equipped with Aethercomm's proprietary DC switching circuitry that enables and disables the DC-DC circuitry in 1000 nSec maximum.
  8. 1000 Watts CW 0.8 – 4.2 GHz Solid-State Amplifier: 1000S1G4

    AR’s 1000S1G4 is a solid-sate amplifier covering the 0.8 – 4.2 GHz frequency range. When used with a sweep generator, it provides a minimum of 1000 watts RF power. Like most of AR’s amplifiers, this model is ideal for applications that call for instantaneous bandwidth, high linearity, and high gain.

  9. Solid-State Microwave Amplifiers

    AR’s solid state amplifier family provides you with the power (1 – 800 watts) and frequency (0.8 to 18 GHz) needed for wireless and EMC testing. These amplifiers boast low spurious signals, noise figures and distortion. They also generate 100% rated power and make it available to the load even when mismatch is severe. In addition, many of the amplifiers is this family allow you to upgrade your existing amplifier to higher power without purchasing new amplifiers as part of the “Subampability” concept.

  10. 60/40 W, 0.7 To 18 GHz Broadband Solid-State Amplifier: 60/40S1G18A

    AR offers the 60/40S1G18A broadband amplifier designed for operation in the 0.7 to 18 GHz range in applications where instantaneous bandwidth, high gain, and linearity are required. This model features low spurious signals, high linearity, and high tolerance, enabling its use in RF applications such as RF susceptibility testing, antenna/component testing, and communication technology testing.