Products and Services

  1. 6-11 GHz Low Noise Amplifier: CMD186P3

    The CMD186P3 is a broadband MMIC low noise amplifier housed in a leadless 3x3 mm plastic surface mount package. The CMD186P3 is ideally suited for EW and communications systems where small size and low power consumption are needed.

  2. 80-100 GHz Balanced Low Noise Amplifier (LNA): ALH495

    This low noise amplifier (LNA) is ideal for applications involving radar, short haul/high capacity links, sensors, millimeter-wave imaging RC chains, and other applications where broad bandwidth and good return loss are important.

  3. Low Noise Amplifiers
  4. Ka Band Low Noise Amplifier: AML1820L3611

    The AML1820L3611 is a low noise amplifier (LNA) that operates in the Ka band.  

  5. MwT-0618S/Z-H5G2: 6 To 18 GHz, Low-Noise, High Gain, Balanced Amplifier Module
    The MwT-0618S-H5G2 and the MwT-0618Z-H5G2 are low noise, high gain open-carrier amplifier modules operating between 6 and 18 GHz. Their input and output ports are matched to 50 O impedance.
  6. Low Noise Amplifiers With High Linearity Offerings: MGA Series
    Avago presents four low-noise amplifiers (LNAs) to extend the RF performance and diversity of its market-leading LNA portfolio. The new modules feature high linearity that improves an application’s ability to distinguish between desired signals and spurious signals received close together. The MGA-6x606 LNAs target WiFi and WiMAX data cards, handsets and other portable devices, while the two-stage MGA-13x16 LNAs target GSM, CDMA and W-CDMA cellular infrastructure applications such as base station radio cards.
  7. 2-26 GHz GaN Low Noise Amplifier: CMD290

    Custom MMIC offers the CMD290 wideband GaAs distributed low noise amplifier operating the 2 to 26 GHz range for applications requiring low noise figure performance and high input power survivability. Delivering 12.5 dB of gain with a corresponding noise figure of 2.3 dB and an output 1 dB compression point of +19 dBm at 13 GHz, this LNA offers RF input survivability of 2 Watts.

  8. Ultra Low Noise, High Linearity Active Bias Low Noise Amplifier: MGA-633P8
    The Ultra Low Noise, High Linearity Active Bias Low Noise Amplifier: MGA-633P8 is the latest addition to the Avago Technologies family of ultra low noise, high gain, high linearity Gallium Arsenide (GaAs) Active Bias Low Noise Amplifiers (LNA). The device provides Best In Class NF (0.38dB @ 900MHz) performance and is designed to be used as first stage LNA within cellular base station transceiver radio cards, tower mounted amplifiers (TMA), combiners, repeaters and remote/digital radio heads.
  9. Low-Noise Amplifiers For S-Band Applications
    These Low Noise Amplifiers are built with GaAs p-HEMT die attached on a ceramic thick film substrate. Alumina, the most commonly used type of ceramic, is what RHIC has chosen due to its relatively high thermal conductivity. These Low Noise Amplifiers are focused on giving the lowest noise possible; exhibiting low noise performance of better than 1dB noise figure. The devices work at input levels as high as 20dBm thanks to the initial gate length of 1200µm design.
  10. Dual-Channel Switch LNA Module: QPB9337

    Qorvo offers the new QPB9337 highly integrated front-end module with operation in the 2.8 – 3.8 GHz frequency range for TDD base station, wireless infrastructure, small cell BTS, and pre-5G/5G massive MIMO applications. This LNA module integrates a two-stage LNA and a high-power switch in a dual-channel configuration.