RF Cables & RF Connectors Solution Center: Rf Cables, & Rf Connectors information

	Microwave/RF Test Assemblies GORE™ PHASEFLEX Microwave/RF Test Assemblies were designed with laboratory and production applications in mind. Available with performance through 110 GHz, the test assemblies provide superior phase and amplitude stability with flexure over a wide temperature range...
	Precision Connector Gage Kit The Maury A042A precision connector gage kit provides a fast and accurate means of checking the center contact and dielectric locations of female SMP connectors and the center contact location of male SMP connectors...
	Filtered D-Sub Connectors Corry Micronics offers filtered d-sub miniature connectors in pin counts from 9 to 37 pins in "C" and "Pi" configurations. Filtered d-sub miniature connector adapters are also available in several different values...
	Coaxial Cable And Waveguides AR provides a complete line of low-loss, microwave coaxial cables. Several connector options and lengths are available. In addition, AR also offers low-loss, microwave waveguides and high-power, double-rigid waveguide-to-coax adapters...
	Reverse-Polarity SMA Connector Connector City's new CONREVSMA015 reverse-polarity SMA connector is suited for applications that require an external antenna on a water-resistant enclosure. The connector has a rubber O-ring that compresses against the outside of the enclosure to prevent water or dust intrusion...
	Capacitive Voltage Probe This NTT Advanced Technology probe is used to measure the voltage of common-mode disturbances conducted along cables. The cable to be measured is clamped in the probe, which is hinged. This probe operates over a wide frequency range with any type of cable...
	Cables/Cable Assemblies Cobham's high-performance, airborne, electronic warfare, RF, and microwave cable assemblies are so tough they must successfully endure 29 torturous environmental tests before receiving the company's seal of approval...
	Quick-Change Solderless Connectors Bird Technologies Group offers quick-change solderless connectors in many different configurations. Because of the wide variety of connectors and possible applications, electrical specifications for QC-equipped products are quoted with the standard connectors normally supplied with equipment...
	Signal Generator For CATV Installation Testing The high-power output of the Merlin signal generator from Noisecom is designed to reduce costly service technician repeat calls due to intermittent cable system problems....
	Filter-In-Connector Series K&L Microwave's Filter-In-Connector Series (FC) is compact, easily installed, and can provide the solution to frequency interference problems. These lumped element filters are available in three to five resonant sections with mechanical lengths of 1.312-inch or 1.536-inch...

Click here for more cables & connectors products.

Cables & Connectors Articles

3-D EM Simulation In The Design Flow Of High-Speed Multi-Pin Connectors
By Thomas Gneiting, AdMOS GmbH, and Adrian Scott, CST AG

This article describes the design flow for a high-speed connector using several simulation tools. The goal is to enable its first pass design without time-intensive and costly iteration steps...

Evaluating The Suitability Of OSP Connectors For Calibration Kit Use
By Paul R. Pino, W.L. Gore & Associates, Inc.

Resulting from a lack of strict adherence to IEEE 287 general precision connector/ laboratory precision connector specifications (GPC/LPC), the Omni-Spectra push-on (OSP) connector type is not generally considered to be suitable for calibration kit use. Although this is the dominant opinion among microwave connector and metrology experts, data that either disputes or confirms this assertion is not readily available...

A High-Power Mechanical Switch Connector Design For Base Station Transceiver Units
By Fabien Bourgeas, Vincent Larrey, and Claude Brocheton, Radiall SA

A mechanical switch connector has been developed that achieves the high isolation required for use in cellular infrastructure transceiver units (TRUs). Electromagnetic simulations and experimentation plans were performed on the switch to optimize its isolation. This article describes the performance of multiple preliminary switch concepts, as well as the parameters of the final, successful design.

Cables & Connectors Downloads

Microwave/RF Assembly Builder
By W.L. Gore & Associates

Gore has developed and proven the effectiveness of a wide range of cable assemblies specifically tailored to the needs of microwave signal transmission. With an unmatched history developing cable assemblies for use in demanding environments, Gore provides the reliable products necessary to meet your individual system requirements.

Catalog: Coaxial Cable Assemblies
By Cobham Sensor Systems

Cable assemblies developed and produced by Cobham cover broad frequency ranges from DC to 50 GHz and are associated with operational ground-based, shipboard, airborne, and space equipment. Many different cable constructions have been developed including reduced loss, scuff resistant, high power, multi-conductor, reduced EMI, extra flexible, and test types...

Custom Cable Assemblies Creator
By Linx Technologies

Connector City's web-based design software allows customers to quickly create the cable assemblies needed for their applications. Customers specify the connectors, cable type, and cable length required and a drawing of the cable assembly is automatically generated so that everything can be visually verified...

Application Note: Simple Cable Coupling Analyses In FEKO
By EM Software & Systems - S.A. (Pty) Ltd. 

Click here for more cables & connectors-related downloads.

Cables & Connectors News

Click here for a comprehensive collection of recent cables & connectors headlines from RF Globalnet's news archive.