RF Military Electronics Featured Datasheets
-
Datasheet: Model 1000A225 Solid-State RF Amplifier
10/27/2009
The Model 1000A225 is a self-contained, air-cooled, broadband, completely solid-state rf amplifier designed for applications where instantaneous bandwidth and high gain are required. Push-pull MOSFET circuitry is utilized in all high power stages in the interest of lowering distortion and improving stability. The Model 1000A225 is equipped with a Digital Control Panel (DCP) which provides both local and remote control of the amplifier. The DCP uses a 3-¾ inch diagonal graphic display, menu assigned softkeys, a single rotary knob, and four dedicated switches (POWER, STANDBY, OPERATE and FAULT/RESET) to offer extensive control and status reporting capability. The display provides operational presentation of Forward Power and Reflected Power plus control status and reports of internal amplifier status.
-
Feedthru Termination: 75L-004 Datasheet
10/21/2009
Designed to match 50-Ohm and 75-Ohm RF devices with an oscilloscope or with other high-impedance test equipment, the JFW feedthru termination has been a trusted component in RF laboratories for decades.
-
Feedthru Termination: 75L-001 Datasheet
10/21/2009
Designed to match 50-Ohm and 75-Ohm RF devices with an oscilloscope or with other high-impedance test equipment, the JFW feedthru termination has been a trusted component in RF laboratories for decades.
-
Feedthru Termination: 50L-001 BNC Datasheet
10/21/2009
Designed to match 50-Ohm and 75-Ohm RF devices with an oscilloscope or with other high-impedance test equipment, the JFW feedthru termination has been a trusted component in RF laboratories for decades.
-
Datasheet: Series 8000: Self-Contained RF Signal Routing Solution
10/6/2009
Series 8000 signal routing solutions are designed and built to customer specifications to match specific requirements for DC, RF/microwave, and optical applications and can be controlled via GPIB (IEEE-488) or LAN. Giga-tronics' custom design capabilities allow system specifiers to define the key design parameters within their applications.
-
Datasheet: Compact Opto-Electronic Oscillator (C-OEO)
10/5/2009
The OEwaves Compact OEO offers extremely low phase noise, low vibration and acceleration sensitivity for signal source modules required in high-frequency and high performance applications. Its unique design, based on microwave photonics, delivers a level of performance that will enable increased capabilities for phase noise measurements, military radar system visibility, channel capacity of communications systems, and future wireless communications systems.
-
Datasheet: RF/Microwave Configurable Switching Chassis - 8300 And 8400 Series
10/2/2009
Giga-tronics recently introduced the Model 8300 and Model 8400 switching chassis’ for its ASCOR switch products optimized for integration into Automated Test Equipment (ATE). With these two new models, test engineers and managers gain access to more than 30 years of signal switching experience and tailored switching solutions for ATE.
-
Datasheet: Wideband Power Amplifier: 50W, 20 To 520 MHz - RWM03060-10
9/30/2009
The RWM03060-10 wideband power amplifier has a minimum 46dB gain & minimum 46dBm P3dB over 20 to 520 MHz. The hybrid amplifiers are compatible with analog, digital, and video waveforms used in ground to ground, ground to air, satellite communications and direct video broadcasting applications. The amplifier includes thermal overload and input power overdrive protection, external voltage variable attenuator port and current monitoring port.
-
Product Overview: Waveguide Switches
9/23/2009
All of Dow Key’s line of Waveguide Switches have an operating voltage of 28 Vdc (24-30 Vdc) and feature an operating temperature of – 54 Degrees C to + 84 Degrees C, and a 200,000 mechanical life cycle minimum. They all can be used in commercial and military applications, while the 3 or 4 port and Waveguide Transfer/SPDT are optimized for commercial, military, avionics, and space applications.
-
Datasheet: Solid State Switching System: 5144
9/23/2009
The 5144 Model RF Switching System is a Solid State Matrix. To compensate for system insertion loss, all inputs are outfitted with high linearity amplifiers. Designed for signal routing this unit can also be used as a building block for ATE applications.