RF Military Electronics Featured Datasheets

  1. Datasheet: IB Series - IB60 Series Surface Mount Filters
    11/6/2009
    IB Series - IB60 Series Surface Mount Filters
  2. Datasheet: IB Series - Lumped Component Microminiature Bandpass Filters
    11/6/2009
    IB Series - Lumped Component Microminiature Bandpass Filters
  3. Datasheet: Maximally Flat 10 dB Coupler
    11/2/2009
    Of the 100 plus in-stock couplers offered by Narda Microwave, the Model 4246B set a sales record in 2009. It out sold its nearest challenger by a factor of two. The product is a maximally flat 10 dB coupler covering the 6 -18 GHz frequency range and is ideally suited for EW systems. Its strip line package is designed for MIL environments and is specified to operate to 105 C without degradation.
  4. Datasheet: Model 1000A225 Solid-State RF Amplifier
    10/27/2009
    The Model 1000A225 is a self-contained, air-cooled, broadband, completely solid-state rf amplifier designed for applications where instantaneous bandwidth and high gain are required. Push-pull MOSFET circuitry is utilized in all high power stages in the interest of lowering distortion and improving stability. The Model 1000A225 is equipped with a Digital Control Panel (DCP) which provides both local and remote control of the amplifier. The DCP uses a 3-¾ inch diagonal graphic display, menu assigned softkeys, a single rotary knob, and four dedicated switches (POWER, STANDBY, OPERATE and FAULT/RESET) to offer extensive control and status reporting capability. The display provides operational presentation of Forward Power and Reflected Power plus control status and reports of internal amplifier status.
  5. Datasheet: Feedthru Termination - Model 75L-004
    10/21/2009
    Designed to match 50-Ohm and 75-Ohm RF devices with an oscilloscope or with other high-impedance test equipment, the JFW feedthru termination has been a trusted component in RF laboratories for decades.
  6. Datasheet: Feedthru Termination - Model 75L-001
    10/21/2009
    Designed to match 50-Ohm and 75-Ohm RF devices with an oscilloscope or with other high-impedance test equipment, the JFW feedthru termination has been a trusted component in RF laboratories for decades.
  7. Datasheet: Feedthru Termination - Model 50L-018
    10/21/2009
    Designed to match 50-Ohm and 75-Ohm RF devices with an oscilloscope or with other high-impedance test equipment, the JFW feedthru termination has been a trusted component in RF laboratories for decades.
  8. Datasheet: Feedthru Termination - Model 50L-001 BNC
    10/21/2009
    Designed to match 50-Ohm and 75-Ohm RF devices with an oscilloscope or with other high-impedance test equipment, the JFW feedthru termination has been a trusted component in RF laboratories for decades.
  9. Datasheet: Series 8000: Self-Contained RF Signal Routing Solution
    10/6/2009
    Series 8000 signal routing solutions are designed and built to customer specifications to match specific requirements for DC, RF/microwave, and optical applications and can be controlled via GPIB (IEEE-488) or LAN. Giga-tronics' custom design capabilities allow system specifiers to define the key design parameters within their applications.
  10. Datasheet: Compact Opto-Electronic Oscillator (C-OEO)
    10/5/2009
    The OEwaves Compact OEO offers extremely low phase noise, low vibration and acceleration sensitivity for signal source modules required in high-frequency and high performance applications. Its unique design, based on microwave photonics, delivers a level of performance that will enable increased capabilities for phase noise measurements, military radar system visibility, channel capacity of communications systems, and future wireless communications systems.